2007 Dodge Magnum HVAC Heater Hose

Part Name: HVAC Heater HoseBrand: DaycoPart#: 80411

Dayco HVAC Heater Hose 80411 - Heater To Tee, Heater To Tee (Inlet), Heater To Pipe

Position: Heater To Tee, Heater To Tee (Inlet), Heater To Pipe

Description:

90 DEGREE COOLANT HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 6
End 1 Inside Diameter : 3/4
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R4 Class D-1, SAE J1684 Type EC

Features:

Dayco® 90 Degree Molded Coolant Hose is designed for vehicles that require special heater hoses with a molded 90 degree elbow to fit tight engine compartment routings. Multiple 90 degree hoses can be used with Dayco plastic connectors to fit complex routings. Knitted reinforcement and all synthetic EPDM construction provides the high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C) that are required for OEM hose replacements. The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose. Dayco’s Molded Radiator and By-Pass Hose has a convenient plastic hang strap for quick and easy merchandising. In addition to meeting SAE J20R4, Class D-1 requirements, this hose is now designed to meet Type EC electro-chemical requirements as specified in SAE J1684.

Condition: New

Fitments

This Part Fits Following 2007 Dodge Magnum Engines.

Engine	Sub Model	Notes	Position
2.7L V6	SE	Top Hose - 90? Molded Coolant Hose	Heater To Pipe
5.7L V8	R/T	90? Molded Coolant Hose	Heater To Tee, Heater To Tee (Inlet)
6.1L V8	SRT8	90? Molded Coolant Hose	Heater To Tee, Heater To Tee (Inlet)

Part Interchange

ACDelco	14592S
ACDelco	14244S
Atlas	MH-71
CARQUEST	18142
CARQUEST	28474
Chrysler	4767172
Datsun/Nissan	92411-0B010
Datsun/Nissan	14055-31U00
Datsun/Nissan	14056-46R00
Duralast	B80411
Ford	F1SE-18472-AA
Ford	F1OY-18472-F
Ford	F32Z-8075-A
Ford	F8CZ-8548-DA
Freshstart	4201
Gates	18142
Gates	28474
General Motors	25537261
General Motors	22646764
General Motors	14099017
General Motors	15530513
General Motors	10190667
General Motors	10188037
General Motors	10135307
General Motors	25525214
General Motors	22601689
General Motors	22612883
General Motors	10065675
General Motors	22610689
General Motors	22602073
Goodyear	63906
Honda	79726-SZA-A00
Mazda	KL11-15-183
Motorcraft	KM3270
NAPA	9815
NAPA	10142

Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: DaycoPart#: 88376

2007 Dodge Magnum HVAC Heater Hose DY 88376

Dayco HVAC Heater Hose 88376 - Tee To Pipe

Position: Tee To Pipe

Description:

MOLDED HEATER HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 10
End 1 Inside Diameter : 3/4
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R3 Class D-1, SAE J1684 Type EC

Features:

Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose in applications where molded hose in small diameters (1" I.D. or smaller) is required. The molded configuration eliminates the need for multiple connections of hoses and clamps. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. If the OE parts have a “quick connect” end, Dayco’s Small I.D. Molded Heater Hoses are also made with the quick connect assembled onto the hose for fast, convenient installation.

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Position
5.7L V8 R/T Hose Must Be Cut On Both Ends - Small I.D. Heater Hose Tee To Pipe
6.1L V8 SRT8 Hose Must Be Cut On Both Ends - Small I.D. Heater Hose Tee To Pipe

Engine	Sub Model	Notes	Position
5.7L V8	R/T	Hose Must Be Cut On Both Ends - Small I.D. Heater Hose	Tee To Pipe
6.1L V8	SRT8	Hose Must Be Cut On Both Ends - Small I.D. Heater Hose	Tee To Pipe

Part Interchange

ACDelco	16155M
ACDelco	14307S
CARQUEST	19727
CARQUEST	19632
Duralast	C88376
Ford	F6AZ-18472-A
Ford	F5AH-18C266-AB
Ford	F8AH-18K579-AC
Ford	F8VH-18K579-AB
Ford	F8AZ-18472-AA
Ford	F8VH-181K579AC
Ford	1W7H-18K579-AB
Ford	1W1H-18K579-AA
Ford	F8VH-18K579-AC
Freshstart	4347
Gates	19632
Gates	19727
Goodyear	63083
NAPA	11727
NAPA	11632
V&W	304376

Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: DaycoPart#: 80413

2007 Dodge Magnum HVAC Heater Hose DY 80413

Dayco HVAC Heater Hose 80413 - Reservoir To Tee

Position: Reservoir To Tee

Description:

90 DEGREE COOLANT HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 18
End 1 Inside Diameter : 3/4
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R4 Class D-1, SAE J1684 Type EC

Features:

Dayco® 90 Degree Molded Coolant Hose is designed for vehicles that require special heater hoses with a molded 90 degree elbow to fit tight engine compartment routings. Multiple 90 degree hoses can be used with Dayco plastic connectors to fit complex routings. Knitted reinforcement and all synthetic EPDM construction provides the high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C) that are required for OEM hose replacements. The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose. Dayco’s Molded Radiator and By-Pass Hose has a convenient plastic hang strap for quick and easy merchandising. In addition to meeting SAE J20R4, Class D-1 requirements, this hose is now designed to meet Type EC electro-chemical requirements as specified in SAE J1684.

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Position
3.5L V6 SE, SXT 90? Molded Coolant Hose Reservoir To Tee

Engine	Sub Model	Notes	Position
3.5L V6	SE, SXT	90? Molded Coolant Hose	Reservoir To Tee

Part Interchange

ACDelco	18155L
ACDelco	16359M
ACDelco	16173M
ACDelco	16172M
CARQUEST	19675
CARQUEST	28476
CARQUEST	19674
Chrysler	4767152
Chrysler	4767152AC
Datsun/Nissan	92400-7S010
Duralast	E80413
Ford	3F1H-18K579-BA
Freshstart	4203
Gates	28476
Gates	19831
Gates	19675
Gates	19674
General Motors	96539591
General Motors	96536531
General Motors	22685161
General Motors	3728191
General Motors	25559279
General Motors	25559278
Goodyear	63303
Goodyear	63918
Goodyear	63304
NAPA	11831
NAPA	9817

Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: GatesPart#: 28474

2007 Dodge Magnum HVAC Heater Hose ZO 28474

Gates HVAC Heater Hose 28474 - Tee-2 To Engine

Position: Tee-2 To Engine

Description:

90 Deg Molded Heater Hose

Part Specifications:

Centerline Length : 10
Arm Length 1 : 4
Arm Length 1 : 101.6
Arm Length 2 : 6
Arm Length 2 : 152.4
Inside Diameter 1 : .75
Angle : 90

Features:

Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
- Engineered to resist electrochemical degradation the leading cause of hose failure.
- Resists water permeation.
- Similar to heater SAE 20R3 Type EC Class D-2.
- Use with heater hose connectors and bulk heater hose for virtually complete molded heater hose coverage.
- Temperature Rating: -40F to 275F (-40C to 135C).
Caution: Do not use for fuel or oil transfer applications.
Gates Powering Progress

Per Car Quantity: 2

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Fit Notes Position
2.7L V6 SE 90º Molded Heater Hose Fuel Type: GAS Tee-2 To Engine
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
2.7L V6	SE	90º Molded Heater Hose	Fuel Type: GAS	Tee-2 To Engine

Part Name: HVAC Heater HoseBrand: GatesPart#: 19360

2007 Dodge Magnum HVAC Heater Hose ZO 19360

Gates HVAC Heater Hose 19360 - Tee-2 To Pipe-2

Position: Tee-2 To Pipe-2

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 12.6
Inside Diameter 1 : .63
Inside Diameter 2 : .75
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Fit Notes Position
6.1L V8 SRT8 Molded Heater Hose Fuel Type: GAS Tee-2 To Pipe-2
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
6.1L V8	SRT8	Molded Heater Hose	Fuel Type: GAS	Tee-2 To Pipe-2

Part Name: HVAC Heater HoseBrand: DaycoPart#: 88361

2007 Dodge Magnum HVAC Heater Hose DY 88361

Dayco HVAC Heater Hose 88361 - Heater To Pipe

Position: Heater To Pipe

Description:

MOLDED HEATER HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 18
End 1 Inside Diameter : 3/4
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R3 Class D-1, SAE J1684 Type EC

Features:

Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose in applications where molded hose in small diameters (1" I.D. or smaller) is required. The molded configuration eliminates the need for multiple connections of hoses and clamps. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. If the OE parts have a “quick connect” end, Dayco’s Small I.D. Molded Heater Hoses are also made with the quick connect assembled onto the hose for fast, convenient installation.

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Position
3.5L V6 SE, SXT Top Hose - Small I.D. Heater Hose Heater To Pipe

Engine	Sub Model	Notes	Position
3.5L V6	SE, SXT	Top Hose - Small I.D. Heater Hose	Heater To Pipe

Part Interchange

ACDelco	16416M
ACDelco	18120L
ACDelco	16511M
ACDelco	18123L
CARQUEST	19627
CARQUEST	19906
CARQUEST	19843
CARQUEST	19614
Chrysler	04596596AC
Duralast	E88361
Ford	F58H-18K580-AA
Freshstart	4399
Gates	19906
Gates	19843
Gates	19627
Gates	19614
General Motors	22551241
General Motors	22537053
General Motors	10037866
General Motors	10024078
Goodyear	63128
NAPA	11843
NAPA	11627
NAPA	11614
NAPA	11906
V&W	304361

Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: DaycoPart#: 80414

2007 Dodge Magnum HVAC Heater Hose DY 80414

Dayco HVAC Heater Hose 80414 - Tee To Reservoir

Position: Tee To Reservoir

Description:

90 DEGREE COOLANT HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 25
End 1 Inside Diameter : 3/4
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R4 Class D-1, SAE J1684 Type EC

Features:

Dayco® 90 Degree Molded Coolant Hose is designed for vehicles that require special heater hoses with a molded 90 degree elbow to fit tight engine compartment routings. Multiple 90 degree hoses can be used with Dayco plastic connectors to fit complex routings. Knitted reinforcement and all synthetic EPDM construction provides the high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C) that are required for OEM hose replacements. The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose. Dayco’s Molded Radiator and By-Pass Hose has a convenient plastic hang strap for quick and easy merchandising. In addition to meeting SAE J20R4, Class D-1 requirements, this hose is now designed to meet Type EC electro-chemical requirements as specified in SAE J1684.

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Position
2.7L V6 SE 90? Molded Coolant Hose Tee To Reservoir

Engine	Sub Model	Notes	Position
2.7L V6	SE	90? Molded Coolant Hose	Tee To Reservoir

Part Interchange

ACDelco	18127L
ACDelco	18136L
ACDelco	18156L
ACDelco	16451M
ACDelco	18128L
CARQUEST	19860
CARQUEST	28477
Datsun/Nissan	92400-0B010
Datsun/Nissan	92400-0B000
Duralast	E80414
Ford	2M5Z-18K359-AD
Ford	YS4Z-18K359-JA
Ford	F3XY-18472-A
Ford	1M5Z-18K359-AA
Ford	F3XY-18472-B
Ford	1M51-18K359-AA
Freshstart	4204
Gates	19657
Gates	19699
Gates	19860
Gates	19660
Gates	28477
General Motors	22731576
General Motors	15280438
Goodyear	63924
Honda	79725-S87-A00
NAPA	11860
NAPA	11699
NAPA	9818
NAPA	11657
NAPA	11660
Pirelli	43924

Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: GatesPart#: 12050

2007 Dodge Magnum HVAC Heater Hose ZO 12050

Gates HVAC Heater Hose 12050 - Oil Cooler Inlet

Position: Oil Cooler Inlet

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 24.2
Inside Diameter 1 : .59
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Fit Notes Position
5.7L V8 R/T Molded Heater Hose Fuel Type: GAS Oil Cooler Inlet
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
5.7L V8	R/T	Molded Heater Hose	Fuel Type: GAS	Oil Cooler Inlet

Part Name: HVAC Heater HoseBrand: GatesPart#: 21832

2007 Dodge Magnum HVAC Heater Hose ZO 21832

Gates HVAC Heater Hose 21832 - Engine To Pipe-1

Position: Engine To Pipe-1

Description:

Molded Coolant Hose

Part Specifications:

Centerline Length : 18
Inside Diameter 1 : .58
Inside Diameter 2 : .72
Number of Branches : 0
Contains Spring : No

Features:

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
- Recommend for upper, lower, by-pass, heater and other coolant hose applications.
- Heat and ozone resistant cover.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Re-engineered materials resist vacuum collapse. This reduces the need for internal springs in many applications.
- Meets SAE 20R4 and 20R3 Type EC Class D-1 and D-2 specifications.
Temperature Rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Fit Notes Position
3.5L V6 SE, SXT Molded Coolant Hose Fuel Type: GAS Engine To Pipe-1
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
3.5L V6	SE, SXT	Molded Coolant Hose	Fuel Type: GAS	Engine To Pipe-1

Part Name: HVAC Heater HoseBrand: GatesPart#: 19652

2007 Dodge Magnum HVAC Heater Hose ZO 19652

Gates HVAC Heater Hose 19652 - Tee-1 To Reservoir

Position: Tee-1 To Reservoir

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 16.5
Inside Diameter 1 : .75
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Fit Notes Position
2.7L V6 SE Molded Heater Hose Fuel Type: GAS Tee-1 To Reservoir
3.5L V6 SE, SXT Molded Heater Hose Fuel Type: GAS Tee-1 To Reservoir
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
2.7L V6	SE	Molded Heater Hose	Fuel Type: GAS	Tee-1 To Reservoir
3.5L V6	SE, SXT	Molded Heater Hose	Fuel Type: GAS	Tee-1 To Reservoir

Part Name: HVAC Heater HoseBrand: DaycoPart#: 86052

2007 Dodge Magnum HVAC Heater Hose DY 86052

Dayco HVAC Heater Hose 86052 - Tee To Reservoir

Position: Tee To Reservoir

Description:

MOLDED HEATER HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 24
End 1 Inside Diameter : 3/4
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R3 Class D-1, SAE J1684 Type EC

Features:

Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose in applications where molded hose in small diameters (1" I.D. or smaller) is required. The molded configuration eliminates the need for multiple connections of hoses and clamps. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. If the OE parts have a “quick connect” end, Dayco’s Small I.D. Molded Heater Hoses are also made with the quick connect assembled onto the hose for fast, convenient installation.

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Position
5.7L V8 R/T Small I.D. Heater Hose Tee To Reservoir
6.1L V8 SRT8 Small I.D. Heater Hose Tee To Reservoir
Part Interchange
ACDelco 16369M
CARQUEST 19837
Chrysler 04596754AC
Duralast E86052
Freshstart 4301
Gates 19837
General Motors 22637179
Goodyear 63015
NAPA 11837
Pirelli 43015
Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Position
5.7L V8	R/T	Small I.D. Heater Hose	Tee To Reservoir
6.1L V8	SRT8	Small I.D. Heater Hose	Tee To Reservoir

Part Name: HVAC Heater HoseBrand: GatesPart#: 19736

2007 Dodge Magnum HVAC Heater Hose ZO 19736

Gates HVAC Heater Hose 19736 - Heater To Tee-2, Tee-1 To Heater

Position: Heater To Tee-2, Tee-1 To Heater

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 7.5
Inside Diameter 1 : .72
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments

This Part Fits Following 2007 Dodge Magnum Engines.

Engine	Sub Model	Notes	Fit Notes	Position
2.7L V6	SE	Molded Heater Hose	Fuel Type: GAS	Heater To Tee-2
5.7L V8	R/T	Molded Heater Hose	Fuel Type: GAS	Heater To Tee-2, Tee-1 To Heater
6.1L V8	SRT8	Molded Heater Hose	Fuel Type: GAS	Heater To Tee-2, Tee-1 To Heater

Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: GatesPart#: 19837

2007 Dodge Magnum HVAC Heater Hose ZO 19837

Gates HVAC Heater Hose 19837 - Tee-2 To Reservoir

Position: Tee-2 To Reservoir

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 25.1
Inside Diameter 1 : .75
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Fit Notes Position
6.1L V8 SRT8 Molded Heater Hose Fuel Type: GAS Tee-2 To Reservoir
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
6.1L V8	SRT8	Molded Heater Hose	Fuel Type: GAS	Tee-2 To Reservoir

Part Name: HVAC Heater HoseBrand: GatesPart#: 24364

2007 Dodge Magnum HVAC Heater Hose ZO 24364

Gates HVAC Heater Hose 24364 - Heater Outlet

Position: Heater Outlet

Description:

Molded Coolant Hose

Part Specifications:

Centerline Length : 14.5
Number of Branches : 1
Inside Diameter 1 : .55
Inside Diameter 2 : .75
Inside Diameter 3 : .75
Contains Spring : No

Features:

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
- Recommend for upper, lower, by-pass, heater and other coolant hose applications.
- Heat and ozone resistant cover.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Re-engineered materials resist vacuum collapse. This reduces the need for internal springs in many applications.
- Meets SAE 20R4 and 20R3 Type EC Class D-1 and D-2 specifications.
Temperature Rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Fit Notes Position
5.7L V8 R/T Molded Coolant Hose Fuel Type: GAS Heater Outlet
6.1L V8 SRT8 Molded Coolant Hose Fuel Type: GAS Heater Outlet
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
5.7L V8	R/T	Molded Coolant Hose	Fuel Type: GAS	Heater Outlet
6.1L V8	SRT8	Molded Coolant Hose	Fuel Type: GAS	Heater Outlet

Part Name: HVAC Heater HoseBrand: GatesPart#: 24365

2007 Dodge Magnum HVAC Heater Hose ZO 24365

Gates HVAC Heater Hose 24365 - Heater Inlet

Position: Heater Inlet

Description:

Molded Coolant Hose

Part Specifications:

Centerline Length : 20.5
Number of Branches : 1
Inside Diameter 1 : .6
Inside Diameter 2 : .7
Inside Diameter 3 : .4

Features:

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
- Recommend for upper, lower, by-pass, heater and other coolant hose applications.
- Heat and ozone resistant cover.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Re-engineered materials resist vacuum collapse. This reduces the need for internal springs in many applications.
- Meets SAE 20R4 and 20R3 Type EC Class D-1 and D-2 specifications.
Temperature Rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2007 Dodge Magnum Engines.
Engine Sub Model Notes Fit Notes Position
5.7L V8 R/T Molded Coolant Hose Fuel Type: GAS Heater Inlet
6.1L V8 SRT8 Molded Coolant Hose Fuel Type: GAS Heater Inlet
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
5.7L V8	R/T	Molded Coolant Hose	Fuel Type: GAS	Heater Inlet
6.1L V8	SRT8	Molded Coolant Hose	Fuel Type: GAS	Heater Inlet

Part Name: HVAC Heater HoseBrand: GatesPart#: 28409

2007 Dodge Magnum HVAC Heater Hose ZO 28409

Gates HVAC Heater Hose 28409 - Pipe-2 To Reservoir, Tee-1 To Reservoir, Tee-2 To Reservoir

Position: Pipe-2 To Reservoir, Tee-1 To Reservoir, Tee-2 To Reservoir

Description:

Straight Heater Hose Standard

Part Specifications:

Centerline Length : 50
Centerline Length : 15.24
Centerline Length : 600
Inside Diameter 1 : .375
Working Pressure : 60
Weight Per Length : 8.25 lbs./Carton

Features:

Premium hose constructed for long service life.
- Unaffected by most coolants and non-oil based coolant additives and by high cooling system pressures
- Good resistance to high temperatures for extended periods of time
- Similar to SAE 20R3 Class D-2
- Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
CAUTION: Do not use for fuel or oil transfer applications.
Gates Powering Progress

Per Car Quantity: 2

Condition: New

Fitments

This Part Fits Following 2007 Dodge Magnum Engines.

Engine	Sub Model	Notes	Fit Notes	Position
2.7L V6	SE	Cut to Length, 28" - Straight Heater Hose (Standard)	Fuel Type: GAS	Tee-2 To Reservoir
3.5L V6	SE, SXT	Cut to Length, 28" - Straight Heater Hose (Standard)	Fuel Type: GAS	Pipe-2 To Reservoir
5.7L V8	R/T	Cut to Length, 32" - Straight Heater Hose (Standard)	Fuel Type: GAS	Tee-1 To Reservoir
6.1L V8	SRT8	Cut to Length, 32" - Straight Heater Hose (Standard)	Fuel Type: GAS	Tee-1 To Reservoir

Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: GatesPart#: 28412

2007 Dodge Magnum HVAC Heater Hose ZO 28412

Gates HVAC Heater Hose 28412 - Pipe To Tee, Pipe-1 To Tee-1, Tee-1 To Heater

Position: Pipe To Tee, Pipe-1 To Tee-1, Tee-1 To Heater

Description:

Straight Heater Hose Standard

Part Specifications:

Centerline Length : 50
Centerline Length : 15.24
Centerline Length : 600
Inside Diameter 1 : .75
Working Pressure : 50
Weight Per Length : 13.20 lbs./Carton

Features:

Premium hose constructed for long service life.
- Unaffected by most coolants and non-oil based coolant additives and by high cooling system pressures
- Good resistance to high temperatures for extended periods of time
- Similar to SAE 20R3 Class D-2
- Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
CAUTION: Do not use for fuel or oil transfer applications.
Gates Powering Progress

Per Car Quantity: 2

Condition: New

Fitments

This Part Fits Following 2007 Dodge Magnum Engines.

Engine	Sub Model	Notes	Fit Notes	Position
2.7L V6	SE	Cut to Length, 13" - Straight Heater Hose (Standard)	Fuel Type: GAS	Pipe To Tee, Tee-1 To Heater
3.5L V6	SE, SXT	Cut to Length, 13" - Straight Heater Hose (Standard)	Fuel Type: GAS	Pipe-1 To Tee-1, Tee-1 To Heater

Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

ACDelco	16369M
CARQUEST	19837
Chrysler	04596754AC
Duralast	E86052
Freshstart	4301
Gates	19837
General Motors	22637179
Goodyear	63015
NAPA	11837
Pirelli	43015

My Vehicle:

2007 Dodge Magnum HVAC Heater Hose

Dayco HVAC Heater Hose 80411 - Heater To Tee, Heater To Tee (Inlet), Heater To Pipe

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 88376 - Tee To Pipe

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 80413 - Reservoir To Tee

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 28474 - Tee-2 To Engine

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 19360 - Tee-2 To Pipe-2

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 88361 - Heater To Pipe

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 80414 - Tee To Reservoir

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 12050 - Oil Cooler Inlet

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 21832 - Engine To Pipe-1

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 19652 - Tee-1 To Reservoir

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 86052 - Tee To Reservoir

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 19736 - Heater To Tee-2, Tee-1 To Heater

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 19837 - Tee-2 To Reservoir

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 24364 - Heater Outlet

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 24365 - Heater Inlet

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 28409 - Pipe-2 To Reservoir, Tee-1 To Reservoir, Tee-2 To Reservoir

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 28412 - Pipe To Tee, Pipe-1 To Tee-1, Tee-1 To Heater

Description:

Part Specifications:

Features:

Related HVAC Parts

What Is MAP Price?

What Is MAP Price?

Core Return Process

Parts list X

Part added to your Kart X

Find exact fit part for your car. X