1996 Isuzu Rodeo HVAC Heater Hose

Part Name: HVAC Heater HoseBrand: DaycoPart#: 88387

Dayco HVAC Heater Hose 88387 - Pipe To Engine

Position: Pipe To Engine

Description:

MOLDED HEATER HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 7
End 1 Inside Diameter : 3/4
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R3 Class D-1, SAE J1684 Type EC

Features:

Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose in applications where molded hose in small diameters (1" I.D. or smaller) is required. The molded configuration eliminates the need for multiple connections of hoses and clamps. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. If the OE parts have a “quick connect” end, Dayco’s Small I.D. Molded Heater Hoses are also made with the quick connect assembled onto the hose for fast, convenient installation.

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Position
3.2L V6 LS, S 45 Degree Hose - Small I.D. Heater Hose Pipe To Engine
Part Interchange
ACDelco 14187S
CARQUEST 19670
Datsun/Nissan 92411-VZ00A
Datsun/Nissan 92413-JK70A
Duralast B88387
Freshstart 4345
Gates 19670
General Motors 25522996
General Motors 10028411
Goodyear 63081
NAPA 11670
V&W 304387
Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Position
3.2L V6	LS, S	45 Degree Hose - Small I.D. Heater Hose	Pipe To Engine

Part Name: HVAC Heater HoseBrand: GatesPart#: 28460

1996 Isuzu Rodeo HVAC Heater Hose ZO 28460

Gates HVAC Heater Hose 28460 - Oil Cooler Pipe-2 To Oil Cooler

Position: Oil Cooler Pipe-2 To Oil Cooler

Description:

90 Deg Molded Heater Hose

Part Specifications:

Centerline Length : 10
Arm Length 1 : 4
Arm Length 1 : 101.6
Arm Length 2 : 6
Arm Length 2 : 152.4
Inside Diameter 1 : .5
Angle : 90

Features:

Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
- Engineered to resist electrochemical degradation the leading cause of hose failure.
- Resists water permeation.
- Similar to heater SAE 20R3 Type EC Class D-2.
- Use with heater hose connectors and bulk heater hose for virtually complete molded heater hose coverage.
- Temperature Rating: -40F to 275F (-40C to 135C).
Caution: Do not use for fuel or oil transfer applications.
Gates Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
3.2L V6 LS, S Cut to fit - 90º Molded Heater Hose Fuel Type: GAS Oil Cooler Pipe-2 To Oil Cooler
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
3.2L V6	LS, S	Cut to fit - 90º Molded Heater Hose	Fuel Type: GAS	Oil Cooler Pipe-2 To Oil Cooler

Part Name: HVAC Heater HoseBrand: GatesPart#: 28474

1996 Isuzu Rodeo HVAC Heater Hose ZO 28474

Gates HVAC Heater Hose 28474 - Pipe-2 To Engine

Position: Pipe-2 To Engine

Description:

90 Deg Molded Heater Hose

Part Specifications:

Centerline Length : 10
Arm Length 1 : 4
Arm Length 1 : 101.6
Arm Length 2 : 6
Arm Length 2 : 152.4
Inside Diameter 1 : .75
Angle : 90

Features:

Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
- Engineered to resist electrochemical degradation the leading cause of hose failure.
- Resists water permeation.
- Similar to heater SAE 20R3 Type EC Class D-2.
- Use with heater hose connectors and bulk heater hose for virtually complete molded heater hose coverage.
- Temperature Rating: -40F to 275F (-40C to 135C).
Caution: Do not use for fuel or oil transfer applications.
Gates Powering Progress

Per Car Quantity: 2

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
3.2L V6 LS, S Cut to fit - 90º Molded Heater Hose Fuel Type: GAS Pipe-2 To Engine
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
3.2L V6	LS, S	Cut to fit - 90º Molded Heater Hose	Fuel Type: GAS	Pipe-2 To Engine

Part Name: HVAC Heater HoseBrand: GatesPart#: 18454

1996 Isuzu Rodeo HVAC Heater Hose ZO 18454

Gates HVAC Heater Hose 18454 - Engine To Oil Cooler Pipe-2

Position: Engine To Oil Cooler Pipe-2

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 6.9
Inside Diameter 1 : .51
Inside Diameter 2 : .82
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
3.2L V6 LS, S Molded Heater Hose Fuel Type: GAS Engine To Oil Cooler Pipe-2
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
3.2L V6	LS, S	Molded Heater Hose	Fuel Type: GAS	Engine To Oil Cooler Pipe-2

Part Name: HVAC Heater HoseBrand: GatesPart#: 19670

1996 Isuzu Rodeo HVAC Heater Hose ZO 19670

Gates HVAC Heater Hose 19670 - Pipe-1 To Engine

Position: Pipe-1 To Engine

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 6.9
Inside Diameter 1 : .75
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
3.2L V6 LS, S Cut to fit - Molded Heater Hose Fuel Type: GAS Pipe-1 To Engine
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
3.2L V6	LS, S	Cut to fit - Molded Heater Hose	Fuel Type: GAS	Pipe-1 To Engine

Part Name: HVAC Heater HoseBrand: DaycoPart#: 80411

1996 Isuzu Rodeo HVAC Heater Hose DY 80411

Dayco HVAC Heater Hose 80411 - Pipe To Engine

Position: Pipe To Engine

Description:

90 DEGREE COOLANT HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 6
End 1 Inside Diameter : 3/4
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R4 Class D-1, SAE J1684 Type EC

Features:

Dayco® 90 Degree Molded Coolant Hose is designed for vehicles that require special heater hoses with a molded 90 degree elbow to fit tight engine compartment routings. Multiple 90 degree hoses can be used with Dayco plastic connectors to fit complex routings. Knitted reinforcement and all synthetic EPDM construction provides the high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C) that are required for OEM hose replacements. The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose. Dayco’s Molded Radiator and By-Pass Hose has a convenient plastic hang strap for quick and easy merchandising. In addition to meeting SAE J20R4, Class D-1 requirements, this hose is now designed to meet Type EC electro-chemical requirements as specified in SAE J1684.

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Position
3.2L V6 LS, S 90 Degree Hose - 90? Molded Coolant Hose Pipe To Engine

Engine	Sub Model	Notes	Position
3.2L V6	LS, S	90 Degree Hose - 90? Molded Coolant Hose	Pipe To Engine

Part Interchange

ACDelco	14592S
ACDelco	14244S
Atlas	MH-71
CARQUEST	18142
CARQUEST	28474
Chrysler	4767172
Datsun/Nissan	92411-0B010
Datsun/Nissan	14055-31U00
Datsun/Nissan	14056-46R00
Duralast	B80411
Ford	F1SE-18472-AA
Ford	F1OY-18472-F
Ford	F32Z-8075-A
Ford	F8CZ-8548-DA
Freshstart	4201
Gates	18142
Gates	28474
General Motors	25537261
General Motors	22646764
General Motors	14099017
General Motors	15530513
General Motors	10190667
General Motors	10188037
General Motors	10135307
General Motors	25525214
General Motors	22601689
General Motors	22612883
General Motors	10065675
General Motors	22610689
General Motors	22602073
Goodyear	63906
Honda	79726-SZA-A00
Mazda	KL11-15-183
Motorcraft	KM3270
NAPA	9815
NAPA	10142

Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: GatesPart#: 18772

1996 Isuzu Rodeo HVAC Heater Hose ZO 18772

Gates HVAC Heater Hose 18772 - Heater To Engine

Position: Heater To Engine

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 15.7
Inside Diameter 1 : .62
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
2.6L L4 LS, S Molded Heater Hose Fuel Type: GAS Heater To Engine
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
2.6L L4	LS, S	Molded Heater Hose	Fuel Type: GAS	Heater To Engine

Part Name: HVAC Heater HoseBrand: DaycoPart#: 87748

1996 Isuzu Rodeo HVAC Heater Hose DY 87748

Dayco HVAC Heater Hose 87748 - Heater To Pipe

Position: Heater To Pipe

Description:

MOLDED HEATER HOSE DAYCO

Part Specifications:

Hose Type : Dual I.D. Hose
Trunk Height : 7
End 1 Inside Diameter : 5/8
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R3 Class D-1, SAE J1684 Type EC

Features:

Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose in applications where molded hose in small diameters (1" I.D. or smaller) is required. The molded configuration eliminates the need for multiple connections of hoses and clamps. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. If the OE parts have a “quick connect” end, Dayco’s Small I.D. Molded Heater Hoses are also made with the quick connect assembled onto the hose for fast, convenient installation.

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Position
3.2L V6 LS, S Short Hose - Small I.D. Heater Hose Heater To Pipe

Engine	Sub Model	Notes	Position
3.2L V6	LS, S	Short Hose - Small I.D. Heater Hose	Heater To Pipe

Part Interchange

ACDelco	14140S
ACDelco	14101S
ACDelco	20338S
CARQUEST	18793
Duralast	B87748
Freshstart	4588
Gates	18793
Gates	19158
Gates	18957
Goodyear	63316
Goodyear	63514
Isuzu	8-97167-696-0
Isuzu	8-97228-088-0
Isuzu	8-97148-220-1
Isuzu	8-97148-220-0
Isuzu	8-97063-882-0
NAPA	10957
NAPA	10793
NAPA	11158

Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Part Name: HVAC Heater HoseBrand: GatesPart#: 21738

1996 Isuzu Rodeo HVAC Heater Hose ZO 21738

Gates HVAC Heater Hose 21738 - Engine To Oil Cooler Pipe-1

Position: Engine To Oil Cooler Pipe-1

Description:

Molded Coolant Hose

Part Specifications:

Centerline Length : 6.6
Inside Diameter 1 : .62
Number of Branches : 0
Contains Spring : No

Features:

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
- Recommend for upper, lower, by-pass, heater and other coolant hose applications.
- Heat and ozone resistant cover.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Re-engineered materials resist vacuum collapse. This reduces the need for internal springs in many applications.
- Meets SAE 20R4 and 20R3 Type EC Class D-1 and D-2 specifications.
Temperature Rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
3.2L V6 LS, S Cut to fit - Molded Coolant Hose Fuel Type: GAS Engine To Oil Cooler Pipe-1
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
3.2L V6	LS, S	Cut to fit - Molded Coolant Hose	Fuel Type: GAS	Engine To Oil Cooler Pipe-1

Part Name: HVAC Heater HoseBrand: GatesPart#: 18797

1996 Isuzu Rodeo HVAC Heater Hose ZO 18797

Gates HVAC Heater Hose 18797 - Heater To Pipe

Position: Heater To Pipe

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 7.7
Inside Diameter 1 : .62
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
2.6L L4 LS, S Molded Heater Hose Fuel Type: GAS Heater To Pipe
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
2.6L L4	LS, S	Molded Heater Hose	Fuel Type: GAS	Heater To Pipe

Part Name: HVAC Heater HoseBrand: GatesPart#: 18793

1996 Isuzu Rodeo HVAC Heater Hose ZO 18793

Gates HVAC Heater Hose 18793 - Heater To Pipe-1

Position: Heater To Pipe-1

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 12.4
Inside Diameter 1 : .62
Inside Diameter 2 : .75
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
3.2L V6 LS, S Cut to fit - Molded Heater Hose Fuel Type: GAS Heater To Pipe-1
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
3.2L V6	LS, S	Cut to fit - Molded Heater Hose	Fuel Type: GAS	Heater To Pipe-1

Part Name: HVAC Heater HoseBrand: GatesPart#: 18205

1996 Isuzu Rodeo HVAC Heater Hose ZO 18205

Gates HVAC Heater Hose 18205 - Intake Manifold To Throttle Body, Throttle Body To Intake Manifold

Position: Intake Manifold To Throttle Body, Throttle Body To Intake Manifold

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 10.9
Inside Diameter 1 : .31
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Per Car Quantity: 2

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
2.6L L4 LS, S Molded Heater Hose Fuel Type: GAS Intake Manifold To Throttle Body, Throttle Body To Intake Manifold
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
2.6L L4	LS, S	Molded Heater Hose	Fuel Type: GAS	Intake Manifold To Throttle Body, Throttle Body To Intake Manifold

Part Name: HVAC Heater HoseBrand: GatesPart#: 19049

1996 Isuzu Rodeo HVAC Heater Hose ZO 19049

Gates HVAC Heater Hose 19049 - Pipe To Engine

Position: Pipe To Engine

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 16.9
Inside Diameter 1 : .6
Inside Diameter 2 : .72
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
2.6L L4 LS, S Cut to fit - Molded Heater Hose Fuel Type: GAS Pipe To Engine
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
2.6L L4	LS, S	Cut to fit - Molded Heater Hose	Fuel Type: GAS	Pipe To Engine

Part Name: HVAC Heater HoseBrand: GatesPart#: 18309

1996 Isuzu Rodeo HVAC Heater Hose ZO 18309

Gates HVAC Heater Hose 18309 - Throttle Body To Engine

Position: Throttle Body To Engine

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 11.7
Inside Diameter 1 : .38
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
3.2L V6 LS, S Molded Heater Hose Fuel Type: GAS Throttle Body To Engine
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
3.2L V6	LS, S	Molded Heater Hose	Fuel Type: GAS	Throttle Body To Engine

Part Name: HVAC Heater HoseBrand: DaycoPart#: 87749

1996 Isuzu Rodeo HVAC Heater Hose DY 87749

Dayco HVAC Heater Hose 87749 - Heater To Pipe

Position: Heater To Pipe

Description:

MOLDED HEATER HOSE DAYCO

Part Specifications:

Hose Type : Dual I.D. Hose
Trunk Height : 8
End 1 Inside Diameter : 5/8
End 2 Inside Diameter : 3/4
Contains Protective Sleeve : Y
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R3 Class D-1, SAE J1684 Type EC

Features:

Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose and provide long, reliable service. Made with the same bends and routing as the OEM assembly, this hose is designed to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. This hose is made with a protective sleeve that protects contact areas against abrasion and heat.

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Position
3.2L V6 LS, S Long Hose - Small I.D. Heater Hose Heater To Pipe
Part Interchange
ACDelco 16111M
ACDelco 1301S
CARQUEST 19130
CARQUEST 18963
Duralast C87749
Gates 18963
Gates 19130
Honda 8-97063-884-0
Isuzu 8-97167-697-0
NAPA 11130
NAPA 10963
Toyota 87245-04140
Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Position
3.2L V6	LS, S	Long Hose - Small I.D. Heater Hose	Heater To Pipe

Part Name: HVAC Heater HoseBrand: GatesPart#: 28409

1996 Isuzu Rodeo HVAC Heater Hose ZO 28409

Gates HVAC Heater Hose 28409 - Pipe-3 To Pipe-4, Pipe-4 To Throttle Body

Position: Pipe-3 To Pipe-4, Pipe-4 To Throttle Body

Description:

Straight Heater Hose Standard

Part Specifications:

Centerline Length : 50
Centerline Length : 15.24
Centerline Length : 600
Inside Diameter 1 : .375
Working Pressure : 60
Weight Per Length : 8.25 lbs./Carton

Features:

Premium hose constructed for long service life.
- Unaffected by most coolants and non-oil based coolant additives and by high cooling system pressures
- Good resistance to high temperatures for extended periods of time
- Similar to SAE 20R3 Class D-2
- Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
CAUTION: Do not use for fuel or oil transfer applications.
Gates Powering Progress

Per Car Quantity: 2

Condition: New

Fitments
This Part Fits Following 1996 Isuzu Rodeo Engines.
Engine Sub Model Notes Fit Notes Position
3.2L V6 LS, S Cut to Length, 3" - Straight Heater Hose (Standard) Fuel Type: GAS Pipe-3 To Pipe-4, Pipe-4 To Throttle Body
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

ACDelco	14187S
CARQUEST	19670
Datsun/Nissan	92411-VZ00A
Datsun/Nissan	92413-JK70A
Duralast	B88387
Freshstart	4345
Gates	19670
General Motors	25522996
General Motors	10028411
Goodyear	63081
NAPA	11670
V&W	304387

ACDelco	16111M
ACDelco	1301S
CARQUEST	19130
CARQUEST	18963
Duralast	C87749
Gates	18963
Gates	19130
Honda	8-97063-884-0
Isuzu	8-97167-697-0
NAPA	11130
NAPA	10963
Toyota	87245-04140

My Vehicle:

1996 Isuzu Rodeo HVAC Heater Hose

Dayco HVAC Heater Hose 88387 - Pipe To Engine

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 28460 - Oil Cooler Pipe-2 To Oil Cooler

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 28474 - Pipe-2 To Engine

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18454 - Engine To Oil Cooler Pipe-2

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 19670 - Pipe-1 To Engine

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 80411 - Pipe To Engine

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18772 - Heater To Engine

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 87748 - Heater To Pipe

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 21738 - Engine To Oil Cooler Pipe-1

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18797 - Heater To Pipe

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18793 - Heater To Pipe-1

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18205 - Intake Manifold To Throttle Body, Throttle Body To Intake Manifold

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 19049 - Pipe To Engine

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18309 - Throttle Body To Engine

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 87749 - Heater To Pipe

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 28409 - Pipe-3 To Pipe-4, Pipe-4 To Throttle Body

Description:

Part Specifications:

Features:

Related HVAC Parts

What Is MAP Price?

What Is MAP Price?

Core Return Process

Parts list X

Part added to your Kart X

Find exact fit part for your car. X