2013 Toyota Tundra HVAC Heater Hose

Part Name: HVAC Heater HoseBrand: GatesPart#: 18335

Gates HVAC Heater Hose 18335 - Thermostat To Engine

Position: Thermostat To Engine

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 7.6
Inside Diameter 1 : .26
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2013 Toyota Tundra Engines.
Engine Sub Model Notes Fit Notes Position
4.0L V6 Base Molded Heater Hose Fuel Type: GAS Thermostat To Engine
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
4.0L V6	Base	Molded Heater Hose	Fuel Type: GAS	Thermostat To Engine

Part Name: HVAC Heater HoseBrand: GatesPart#: 18337

2013 Toyota Tundra HVAC Heater Hose ZO 18337

Gates HVAC Heater Hose 18337 - Pipe-2 To Thermostat

Position: Pipe-2 To Thermostat

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 6.5
Inside Diameter 1 : .26
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2013 Toyota Tundra Engines.
Engine Sub Model Notes Fit Notes Position
4.0L V6 Base Molded Heater Hose Fuel Type: GAS Pipe-2 To Thermostat
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
4.0L V6	Base	Molded Heater Hose	Fuel Type: GAS	Pipe-2 To Thermostat

Part Name: HVAC Heater HoseBrand: GatesPart#: 18336

2013 Toyota Tundra HVAC Heater Hose ZO 18336

Gates HVAC Heater Hose 18336 - Thermostat To Pipe-1

Position: Thermostat To Pipe-1

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 8.7
Inside Diameter 1 : .63
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2013 Toyota Tundra Engines.
Engine Sub Model Notes Fit Notes Position
4.0L V6 Base Molded Heater Hose Fuel Type: GAS Thermostat To Pipe-1
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
4.0L V6	Base	Molded Heater Hose	Fuel Type: GAS	Thermostat To Pipe-1

Part Name: HVAC Heater HoseBrand: GatesPart#: 19025

2013 Toyota Tundra HVAC Heater Hose ZO 19025

Gates HVAC Heater Hose 19025 - Pipe-1 To Pipe-2

Position: Pipe-1 To Pipe-2

Description:

Molded Heater Hose

Part Specifications:

Centerline Length : 7.1
Inside Diameter 1 : .59
Number of Branches : 0

Features:

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
- Similar to OEM specifications.
- Has all the quality features of Gates Molded Coolant Hose.
- Engineered to resist electrochemical degradation - the leading cause of hose failure.
- Inside diameters range from 1/4 to 1 .
- Meets SAE 20R3 type EC Class D-1 and D-2 specifications.
Temperature rating: -40 F to 275 F (-40 C to 135 C) in coolant hose applications.
Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates - Powering Progress

Condition: New

Fitments
This Part Fits Following 2013 Toyota Tundra Engines.
Engine Sub Model Notes Fit Notes Position
4.0L V6 Base Cut to fit - Molded Heater Hose Fuel Type: GAS Pipe-1 To Pipe-2
Warranty & Easy Return
Manufacturer’s Warranty : Limited Lifetime
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Fit Notes	Position
4.0L V6	Base	Cut to fit - Molded Heater Hose	Fuel Type: GAS	Pipe-1 To Pipe-2

Part Name: HVAC Heater HoseBrand: DaycoPart#: 87884

2013 Toyota Tundra HVAC Heater Hose DY 87884

Dayco HVAC Heater Hose 87884 - Heater Outlet

Position: Heater Outlet

Description:

MOLDED HEATER HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 13
End 1 Inside Diameter : 5/8
End 1 Outside Diameter : 15/16
End 2 Inside Diameter : 5/8
End 2 Outside Diameter : 15/16
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R3 Class D-1, SAE J1684 Type EC

Features:

Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose in applications where molded hose in small diameters (1" I.D. or smaller) is required. The molded configuration eliminates the need for multiple connections of hoses and clamps. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. If the OE parts have a “quick connect” end, Dayco’s Small I.D. Molded Heater Hoses are also made with the quick connect assembled onto the hose for fast, convenient installation.

Condition: New

Fitments
This Part Fits Following 2013 Toyota Tundra Engines.
Engine Sub Model Notes Position
4.6L V8 Base, SR5 Cut to Fit - Small I.D. Heater Hose Heater Outlet
5.7L V8 Base, Limited, Platinum, SR5 Cut to Fit - Small I.D. Heater Hose Heater Outlet
Part Interchange
ACDelco 16539M
ACDelco 18242L
CARQUEST 18029
CARQUEST 19117
Duralast D87884
Gates 19117
Gates 18029
General Motors 19130010
General Motors 15263237
NAPA 10029
NAPA 11117
Toyota 87245-0C210
Toyota 87245-0C211
Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

Engine	Sub Model	Notes	Position
4.6L V8	Base, SR5	Cut to Fit - Small I.D. Heater Hose	Heater Outlet
5.7L V8	Base, Limited, Platinum, SR5	Cut to Fit - Small I.D. Heater Hose	Heater Outlet

Part Name: HVAC Heater HoseBrand: DaycoPart#: 87806

2013 Toyota Tundra HVAC Heater Hose DY 87806

Dayco HVAC Heater Hose 87806 - Heater Inlet

Position: Heater Inlet

Description:

MOLDED HEATER HOSE DAYCO

Part Specifications:

Hose Type : Single I.D. Hose
Trunk Height : 5 1/2
End 1 Inside Diameter : 5/8
End 2 Inside Diameter : 5/8
Contains Protective Sleeve : N
Contains Heat Shield : N
Color : Black
Material : EPDM
SAE Specification : SAE J20R3 Class D-1, SAE J1684 Type EC

Features:

Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose in applications where molded hose in small diameters (1" I.D. or smaller) is required. The molded configuration eliminates the need for multiple connections of hoses and clamps. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40°F (-40°C) to +257°F (+125°C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. If the OE parts have a “quick connect” end, Dayco’s Small I.D. Molded Heater Hoses are also made with the quick connect assembled onto the hose for fast, convenient installation.

Condition: New

Fitments
This Part Fits Following 2013 Toyota Tundra Engines.
Engine Sub Model Notes Position
4.6L V8 Base, SR5 Small I.D. Heater Hose Heater Inlet
5.7L V8 Base, Limited, Platinum, SR5 Small I.D. Heater Hose Heater Inlet

Engine	Sub Model	Notes	Position
4.6L V8	Base, SR5	Small I.D. Heater Hose	Heater Inlet
5.7L V8	Base, Limited, Platinum, SR5	Small I.D. Heater Hose	Heater Inlet

Part Interchange

ACDelco	14113S
ACDelco	14558S
ACDelco	16060M
CARQUEST	18028
CARQUEST	18789
CARQUEST	18810
Duralast	C87806
Gates	18789
Gates	18810
Gates	18028
Honda	79720-SD4-000
Kia	0K019-61-212E
Kia	0K019-61-212
NAPA	10028
NAPA	10789
NAPA	10810
Toyota	87245-0C200
Toyota	87245-0C201

Warranty & Easy Return
Manufacturer’s Warranty : 12 Months/12,000 Miles
You can return the part within 30 days for any reasons.
After 30 days, all parts are covered under manufacturer’s warranty or 2 years whichever is the highest.
Refunds get issued within 24 to 48 hours to your mode of payment after return part received.

My Vehicle:

2013 Toyota Tundra HVAC Heater Hose

Gates HVAC Heater Hose 18335 - Thermostat To Engine

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18337 - Pipe-2 To Thermostat

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18336 - Thermostat To Pipe-1

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 19025 - Pipe-1 To Pipe-2

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 87884 - Heater Outlet

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 87806 - Heater Inlet

Description:

Part Specifications:

Features:

Related HVAC Parts

ACDelco	16539M
ACDelco	18242L
CARQUEST	18029
CARQUEST	19117
Duralast	D87884
Gates	19117
Gates	18029
General Motors	19130010
General Motors	15263237
NAPA	10029
NAPA	11117
Toyota	87245-0C210
Toyota	87245-0C211

My Vehicle:

2013 Toyota Tundra HVAC Heater Hose

Gates HVAC Heater Hose 18335 - Thermostat To Engine

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18337 - Pipe-2 To Thermostat

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 18336 - Thermostat To Pipe-1

Description:

Part Specifications:

Features:

Gates HVAC Heater Hose 19025 - Pipe-1 To Pipe-2

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 87884 - Heater Outlet

Description:

Part Specifications:

Features:

Dayco HVAC Heater Hose 87806 - Heater Inlet

Description:

Part Specifications:

Features:

Related HVAC Parts

What Is MAP Price?

What Is MAP Price?

Core Return Process

Parts list X

Part added to your Kart X

Find exact fit part for your car. X